GE燃机卡IS200EPSMG2A模块通用电气

Turnlok Plug 50A 600V 250VDC 3 Pole 4W, 3765, Hub 3765C, HUB3765C 1473W

Hansen Quick Disconnect Series 8000, 1/2 NPT, Shipsameday 170P3

GRANVILLE-PHILLIPS 275 MINI CONVECTRON, 275538-GD-T, SHIPSAMEDAY 1610TK

GLENAIR BACKSHELL 06324-390AS005NF0803A3, SHIPSAMEDAY 1557F

KEYENCE KV-40DT, KV40DT, Base unit DC type 24 Inputs &16 Tran Outputs130B13

Tubing, 316L SS, PP04261049-2A, 1473A12

Square D Control Relay, 8501-G080, 8501G080, NNB, 120 Coil, Shipsameday 1543AX

Swagelok Flexible Metal, 14 x 3/8npt x 3/8 Comp, SS-FM6SL6PM6-14, ZE4

产品描述IC2ALG261是GE Fanuc Versamax系列的8通道15位输入模块。该模拟输入模块提供了一个8个差分电压输入的接口，并通过背板电源供电。该模块的之处在于外部电源操作。但是，用户收发器的电源具有外部电源。否则，该模块具有一组八个差分输入通道，具有15位转换器分辨率和软件可配置选择。IC2ALG261的特定特性包括25VAC连续输入逻辑，LED指示灯和5V输出，背板电流消耗为2mA。诊断将提醒用户电源丢失；但是，如果发生严重的RF干扰，精度可能会降+/- 1。在安装之前，应仔细检查设备是否损坏。如果发现损坏，请换系统以使其正常运行。安装后，如果模块的热未正确完成，则该背板上其他模块的操作可能会中断。对于模拟通道连接，建议使用双绞线，如果可能，该电缆应在源设备上接地。如果源设备不是接地选项，则使用I / O模块接地。如果需要增加连接，则可以在中间端子上添加辅助I / O端子排。该IC2ALG261是与包括PLC CPU 2.1或高版本和以太网NIU EBI1版本1.1或高版本固件的众多版本兼容。指标频道数： 8个差速器，一组电压范围 -1至+1伏直流电当前范围： 不适用新率： 7.5毫秒输入过滤器响应： 不适用能量消耗： + 5V总线2mA

大量供应DCS系统的配件，PLC系统的配件。
主营：本特利，英维思，伍德沃德，福克斯波罗、西屋、瑞恩、施耐德莫迪康、ABB、AB、西门子、摩托罗拉、GE发那科、安川、博世力士乐，ACSO，YOKOGAWA横河，力士乐等各的DCS系统配件，机器人系统配件，大型伺服系统备件国外直接采购，原装行货，优惠，售后保修，型号，库存，欢迎电话查询！工业设备 ABB、施耐德140/TSX、AB等系统卡件、伺服控制器、电源模块、CPU模块、PLC系统控制器
IC200CHS022
S200SSBAG1A
IS200ERIOH1A
IS200SRLYH2AAA
IS200AEBMG1AFB
IS200AEBMG1AFBIS200
IS220PPROH1A
IS220PAICH1
IS220PTURH1A
IS200DAMDG1A
IS200EPSMG2A
IS220PAICH1A
IS210AEACH1ABB
IS220PDIOH1A
IS220PDIAH1A
IS200VTURH2B
DS200SDCCG5A
DS200PCCAG5A
DS200FHVAG1A
DS200IIBDG1AEAD
DS200UDSAG1AAAD
DS200SHVMG1AFE
DS200SDCCIAG
DS200DMCAG1EA
DS200DMCBG1ACC
DS200IPCSG1AD
DS200UPLAG1ADC
DS200LPPAG1ABA
DS200SDCIG1AGB
DS200ADPBG1A
DS200RTBAG3AFB
DS200RTBAG3AGC
DS200DTBAG1AAA
DS200DTBAG1A
DS200SLCCG1AEF
DS200SLCCG1A
DS200IIBDG1ADA
DS200IIBDG1A
The IS200VSVOH1B is a board component made by General Electric for the Mark VI.The Mark VI was released by GE as part of their long-running and popular Speedtronic line for gas/steam turbine management, which began in the 1960s when the company released the Mark I system. This line of turbine control has continued development on through to the 2000s with the Mark VI and Mark VIe. The Mark VI includes Ethernet communications capabilities, a PC-based operator interface, and integrated hardware and software that are both designed specifically for turbine control.
The IS200VSVOH1B functions as a Servo Control board. The board drives fuel/steam valves through its control of four electro-hydraulic servo valves. The board also provides pulse rate flow inputs, LVDT excitation, and LVDT position feedback. The IS200VSVOH1B can be used in Triple Redundant systems and also in Simplex systems.

The IS200VSVOH1B is has a single slot front panel attached to the PCB. This panel includes a cable connector (J5) as well as LED indicators for status information. The three LEDs in the front panel include a RUN light (green,) a FAIL light (red,) and a STATUS light. The STATUS light typically is not powered. However, if an alarm condition is present this LED will be powered up and will display as a steady orange.

The IS200VSVOH1B has six connectors, including two backplanes (P1/P2,) and four connectors made with conductive traces (P3 through P6.) The board includes four relays (K1 through K4.) Each of these components has a printed diagram on its top surface. The board is populated with resistors, capacitors, and TP test points. It also has inductor beads (L1-L10.) The board has over seventy integrated circuits.